Muncie PTO and Parts Discount Priced and Delivered.

The Muncie PTO and parts discount outlet, where you can Buy Direct and Save!

We ship to any location.

855 844-SALE
        
Get Muncie parts manuals and look up information by going directly to Parts Manuals Page. or click on your model below for service and owners manuals for that model. PTO parts break-downs and arrangement drawing are available in the parts manual for each model.

Available Muncie PTO Models:

* Alpha Series PTO
* 82 Series PTO
* 8405A Series PTO
* 8406A Series PTO
* CD10 Series PTO
* CD40 Series PTO
* CS6 Series PTO
* CS8 Series PTO
* CS10 Series PTO
* CS11 Series PTO
* CS20 Series PTO
* CS21 Series PTO
* CS41 Series PTO
* FA Series PTO
* FR Series PTO
* GA Series PTO
* GB Series PTO
* GM Series PTO
* HS24 Series PTO
* RS Series PTO
* SG Series PTO
* SH Series PTO
* SS66 Series PTO
* SSH2 Series PTO
* SSV2 Series PTO
* TG Series PTO
* Reversible PTO Series
* Gear Adapters
* Shaft Extensions

Muncie PTO Installation:

* Not all units will make noises when improperly spaced so careful inspection is required on every installation to prolong the life of the PTO and the transmission gears. Extra caution must be used when geared adapters are used, so be sure to double check the spacing. Automatic transmissions have higher noise levels caused by the thinner transmission fluid so proper spacing is mandatory.

The owner's manual for each PTO (available to download) will give you the correct backlash adjustment which is needed on every PTO installation. The spacing between the transmission and PTO should be from .006 to .012.

To much space will cause the PTO to rattle or chatter when running with no load. To correct this you can remove one or more of the mounting gaskets to get the proper spacing and test it again.

To little spacing will cause PTO to squeal or whine and may cause difficulties in shifting the PTO and or the transmission. To correct this, add another mounting gasket or gaskets and test it again.

To build the proper Muncie PTO for your application, we need the following information:

1. The transmission model number.
2. What side will you mount the PTO on.
3. How will you shift the P.T.O, (Cable, Air, Electric, Lever)
4. How will the pump be mounted, direct or driveshaft.
5. Type of truck are you building, (Roll Off, Wrecker, Dump Bed, Pump Truck)
6. Percentage of engine speed needed.
7. GPM if pump is also needed.

Muncie PTO Pumps:
Std Gear Pumps:
PF, PH, PK, PKS and PM Series Pumps.

Clutch Pumps:
PF, PF2 and PH Models.

Dump Pumps:
E2, E3, EH2, EH3, S2, S3, S4 and S5 Units.

Refuse and Specialty Gear Pump Models:
MLSA, Power Miser L and M Series, Power Pro L and M Models and MLSM Live-Pak.

Vane Pumps:
A, B, C, C Quiet Pak, D, D Quiet Pak and E Models.

Piston Pump Models:
PV2, PVC, PP, PQ, PR and PR Tandem and PT Units in stock.

To determine what hydraulic pump is needed for your PTO application we need the following information:

1. Gallons per minute your equipment requires.
2. What RPM: engine speed is needed to operate the equipment.
3. Percent of engine speed needed to set the ratio.
4. Operating pressure or PSI the equipment manufacturer recommends.

Muncie Wet Line Kits:
For wet line kits we need:

1. Type of trailer or types of trailers to be used.
2. What model transmission is in truck. (Data tag information off the transmission).
3. Where will the PTO be mounted.
4. Where will the pump be mounted.
5. How do you want to operate the setup.
6. What type of controls will you use, air, cable, electric.
7. If you require a hydraulic oil reservoir, will it mount on the frame rail or behind the cab.

You can also Contact us for expert assistance on any PTO or more information when needed. We are here to assist you in any way we can and offer Power take off products factory direct for all makes and models.

The PTO Supply also offers parts, sales, service and repairs for:
Chelsea, Bezares, NewStar and Metaris PTOs.